共查询到20条相似文献,搜索用时 984 毫秒
1.
挤出口模在挤出成型中发挥着重要作用,其口模设计的是否合理关系着挤出制品的质量和挤出成本。因此本文应用polyflow软件,采用PTT粘弹本构,分析方管口模几何尺寸与气辅挤出口模内外的各场量之间的变化规律(如改变滑移段长度、口模壁厚及口模截面积观察挤出压降、速度及剪切速率的变化)。确定出方管挤出口模的合理几何结构和尺寸,设计出方管型气辅挤出口模,从而提高口模设计精度和产品的质量,并降低生产成本。 相似文献
2.
本文基于拥有自主知识产权的有限元程序自动生成平台FEPG,采用具有二阶精度的CBS方法,初步建立了应用于微小流道计算的双流体模型有限元结构化程序。分析了多种流道结构形式含单级泥沙组分滴头内的流场与泥沙组分浓度分布的数值模拟结果,与实验研究结果进行对比的结果表明数值结果与实验吻合良好,该双流体模型有限元程序是有效的,可用于微小流道结构的流场模拟。 相似文献
3.
采用FLUENT软件,应用标准k-湍流模型和混合网格,采用分离隐式求解器,对某离心风机三维流场进行了CFD数值计算分析。计算表明:虽风机内部流场速度分布比较均匀,无明显的漩涡、二次流等出现,但风机内部流场顺畅性不佳,有待改进。 相似文献
4.
5.
应用三维软件Pro/E进行SCR催化转化器建模,使用CFD软件AVLFire对建立的SCR催化转化器模型流场、速度均匀性进行模拟,根据模拟结果对数模结构优化,按优化前后的图纸进行封装,并对比测试优化前后的SCR催化转化器背压和催化转化效率。 相似文献
6.
分析一些挤出模具的定型模,可以明显地看出他们的设计所追求的主要目标是冷却成型的均匀性,而不是简单的冷却效率。本文运用ANSYS模拟软件,对塑料异型材功能块部位在挤出定型套中的冷却状况进行数值分析,针对异型材生产过程中的一些不稳定现象给出理论解释,从而为挤出定型套冷却系统合理设计与使用提供依据。 相似文献
7.
8.
束江军 《内蒙古科技与经济》2014,(5):101+103-101,103
对螺杆空气压缩机机头排气温度高的原因进行了分析,提出了采用机械物理方法对压缩机油冷却器及油路进行全面清洗,解决机头排气温度故障,确保压缩机正常运行的方法。 相似文献
9.
10.
<正>借助Fluent软件分析旋风分离器内部流场的运动状况,采用k-epsilon对切向入口的旋风分离器内流场进行了三维数值模拟研究。数值结果表明,分离器内部的流动空间可分为内、外2个流动区域,在不同的流动区域中,气体压力、速度场的分布有较大的差异。而且压力分布与速度分布不是轴对称分布。数值模拟结果对其设计优化研究有一定的应用价值。 相似文献
11.
12.
Understanding the mechanical properties of optically transparent polydimethylsiloxane (PDMS) microchannels was essential to the design of polymer-based microdevices. In this experiment, PDMS microchannels were filled with a 100 μM solution of rhodamine 6G dye at very low Reynolds numbers (∼10−3). The deformation of PDMS microchannels created by pressure-driven flow was investigated by fluorescence microscopy and quantified the deformation by the linear relationship between dye layer thickness and intensity. A line scan across the channel determined the microchannel deformation at several channel positions. Scaling analysis widely used to justify PDMS bulging approximation was allowed when the applied flow rate was as high as 2.0 μl/min. The three physical parameters (i.e., flow rate, PDMS wall thickness, and mixing ratio) and the design parameter (i.e., channel aspect ratio = channel height/channel width) were considered as critical parameters and provided the different features of pressure distributions within polymer-based microchannel devices. The investigations of the four parameters performed on flexible materials were carried out by comparison of experiment and finite element method (FEM) results. The measured Young''s modulus from PDMS tensile test specimens at various circumstances provided reliable results for the finite element method. A thin channel wall, less cross-linker, high flow rate, and low aspect ratio microchannel were inclined to have a significant PDMS bulging. Among them, various mixing ratios related to material property and aspect ratios were one of the significant factors to determine PDMS bulging properties. The measured deformations were larger than the numerical simulation but were within corresponding values predicted by the finite element method in most cases. 相似文献
13.
明渠中水流的运动要素不随时间而变化时,称为明渠恒定流;否则称为明渠非恒定流。明渠恒定流中,如果水流流线是一簇平行的直线,且水深、断面平均流速沿程不变,称为明渠恒定均匀流;如果流线不是平行直线,则称为明渠恒定非均匀流。 相似文献
14.
15.
16.
17.
为了体现功能梯度材料的耐高温性,本文采用顺序耦合法,通过对Cu和WC组成的双材料和功能梯度材料在热-机耦合作用下进行了ANSYS有限元模拟,结果表明,功能梯度材料较双材料具有大大缓和热应力的作用,同时也证明了Cu/WC功能梯度材料较双材料更适合用作大电流滑动触头用耐磨材料。 相似文献
18.
当谈及日语"上"的方位表达方式时,中文用"名词+上"来表达,而日语却用"名词+上+に、で…"来表达。比如将"桌子上有书"这个句子翻译成日语时,一般可以这样翻译:"机の上に本がある"。用同样的方法将"黑板上有字"翻译成日语,就会翻译成"黒板の上に字がある",但这个日语句子却变成了"黑板的上方有字"的意思了。也就是说中国的"名词+上"和日语的"名词+上+に、で…"并非一对一的关系。那么这两者到底是怎样的关系呢?同时,二外日语学习者对这一语言现象的习得状况又如何呢?本文以将日语作为第二外语的英语专业的二外日语学习者为对象,对其习得状况进行实证调查,并究其问题所在,然后从中日对照的角度对二外日语学习者的日语方位表达方式"上"的教学方略进行探讨。 相似文献
19.
Sohrab Enayati Seyed Ali Asghar Akbari Mousavi Seyed Mohammad Ebrahimi Majid Belbasi Mostafa Sultan Bayazidi 《Journal of The Franklin Institute》2011,348(10):2813-2822
In this study, the hot backward extrusion of Ti–6Al–4V alloy is considered by finite element analysis and experiments. The effects of reduction and initial billet temperature on the force required for extrusion, on the maximum strain produced and on the formation of surface cracks are discussed. The simulation results show that the increase of temperature at high reduction is considerable and that can be reached 150 °C in the billet and punch interface. Moreover, the maximum strain is predicted at the interface of billet and punch. The study shows that the temperature rise and plastic deformation may induce surface cracks. 相似文献
20.
钢管支架是土木工程施工过程中经常运用的一种支撑结构。在保证支架结构强度、刚度和稳定性要求的基础上也需要考虑它的经济性。本文以某斜拉桥为背景,用ANSYS通用有限元软件建立了四种空间有限元支架模型并进行比较分析,为桥梁施工提供理论依据。 相似文献