共查询到20条相似文献，搜索用时 546 毫秒
1.
A type of hollow cylinder joints connected with H-shaped beams is proposed for spatial structures. Based on von Mises yield
criterion and perfect elasto-plasticity model, a series of finite element models of the joints is established, in which the
effect of geometric nonlinearity is taken into account. Then mechanical behavior and load-carrying capacity of the joints
were investigated, which were subjected to axial load, in- and out-plane bending moments, and their combinations. The results
show that the ultimate loads of the joints are determined by the maximum displacement. Furthermore, the case of one joint
connected with multiple beams was discussed. Experiments on a set of typical full-scale joints were conducted to understand
the structural behavior and the failure mechanism of joint, and also to validate the finite element models. Finally, the practical
calculation method was established through finite elements analysis (FEA) results and numerical fitting. The results show
that the joints are more ductile and materially economical than welded hollow spherical joints, and the practical calculation
method can provide a reference for direct design and the revision of relevant design codes. 相似文献
2.
Seismic behavior of diaphragm-through connections of concrete-filled square steel tubular columns and H-shaped steel beams 总被引：1，自引：1，他引：0
Based on the introductions of a type of diaphragm-through connection between concrete-filled square steel tubular columns (CFSSTCs) and H-shaped steel beams,a finite element model of the connection is developed and used to investigate the seismic behavior of the connection.The results of the finite element model are validated by a set of cyclic loading tests.The cyclic loading tests and the finite element analyses indicate that the failure mode of the suggested connections is plastic hinge at the beam with inelastic rotation angle exceeding 0.04 rad.The suggested connections have sufficient strength,plastic deformation and energy dissipation capacity to be used in composite moment frames as beam-to-column rigid connections. 相似文献
3.
FRP加固RC圆柱正截面受弯承载力计算（英文） 总被引：1，自引：0，他引：1
运用数值计算方法对FRP加固钢筋混凝土（RC）圆柱截面特性进行计算,发现截面破坏时受压区高度主要受轴压比、FRP约束强度比和纵筋配筋特征值3个主要参数影响.根据数值计算的结果进行回归,提出了受压区对应圆心角θ的计算方法.数值计算结果显示,横向约束导致的混凝土应力提高以及纵筋屈服后的强化效应使RC柱破坏时截面受弯承载力远大于规范规定值.根据理论分析和36个大比例试件实测结果提出截面破坏时受弯承载力计算方法,计算结果与试验结果吻合很好.最后,对一个典型柱变形能力进行参数分析,研究轴压比,纵筋配筋特征值和FRP约束强度比对正截面变弯承载力的影响.结果显示FRP加固圆柱破坏时受弯承载力可以比规范规定的未加固柱受弯承载力提高50%左右. 相似文献
4.
Shear failure in panel zones and plastic hinges in steel beams are the two major failure modes of connections between concrete-filled steel tubular(CFST) columns and steel beams. To investigate the behavior of this type of connection in both modes,two through-diaphragm connections were tested under cyclic and monotonic loadings and the load-carrying capacity,ductility,and strength of degradation of connections were discussed. Using ABAQUS software,we developed nonlinear finite-element models(FEMs) to simulate the load-carrying capacity and failure modes of the connections under monotonic loading. The finite-element(FE) analysis and test results showed reasonable agreement for the through-diaphragm connections,which confirms the accuracy of FEMs in predicting the load-carrying capacity and failure modes of connections. Based on the validated FEM,a parametric study was then conducted to investigate the infl uence of the thicknesses of the tube and diaphragm on the load-carrying capacity and failure modes of these connections. The results indicate that the strength,stiff ness,and load-carrying capacity are infl uenced less by the thickness of the diaphragm,and more by the thickness of the steel tube. According to the FE analysis results,it can be found that the critical condition between the two failure modes is determined by the shear resistance and bending resistance. 相似文献
5.
文章通过SAP2000程序,建立了半刚性组合节点理论分析模型,采用转动弹簧单元来模拟实际中钢管柱与组合梁的半刚性连接。通过分析比较节点在低周反复荷载作用下的荷载(P)-位移(Δ)关系滞回曲得到,组合节点的承载力、刚度和耗能能力有所提高,耗能较好,但承载力相差不大,所以在正常的施工条件下,应优先选用方钢管。 相似文献
6.
Dynamic response of RPC-filled steel tubular columns with high load carrying capacity under axial impact loading 总被引：3，自引：0，他引：3
Experimental investigation into impact-resistant behavior of reactive powder concrete (RPC)-filled steel tubular columns was conducted,and dynamic response of the columns under axial impact loading was studied by means of numerical simulation method.Increase coefficient of load carrying capacity and ratio of load carrying capacity between steel tube and RPC core of col-umns were obtained. 相似文献
7.
为了研究钢筋增强ECC梁受弯性能,进行了钢筋增强ECC梁和普通钢筋混凝土梁受弯的对比研究.结果表明,相比普通钢筋混凝土梁,钢筋增强ECC梁的受弯承载力和延性分别提高了24.8%和187.76%,并且在梁中用ECC代替混凝土可有效延缓裂缝的发展.此外,采用简化的ECC本构模型对钢筋增强ECC及混凝土梁的受弯性能进行了非线性有限元分析,模拟结果与试验结果吻合较好,在服役期间钢筋增强ECC梁的裂缝可以控制在0.4 mm以下.ECC材料的使用可明显提高梁的抗弯承载力、变形能力、延性等受弯性能. 相似文献
8.
根据内置CFRP圆管的方钢管高强混凝土的特点,通过引入混凝土强度折减系数和等效约束折减系数,将内置CFRP圆管的方钢管高强混凝土等效为内置CFRP圆管的圆钢管高强混凝土。进而,在统一强度理论的基础上,推导出内置CFRP圆管的方钢管高强混凝土轴压构件的强度承载力。通过引入整体稳定系数,推导出内置CFRP圆管的方钢管高强混凝土轴压中长柱的稳定极限承载力公式。将该公式的计算结果与试验结果进行了比较,结果表明该理论公式是正确可行的。理论公式以期能为工程应用提供帮助。 相似文献
9.
随着钢结构的发展,钢管搭接节点应用越来越广泛.钢结构中节点受力最复杂,目前对平面K型钢管搭接节点的静力研究有很好的基础.但是在低周往复荷载下节点滞回性能的分析还比较少.采用有限元法对平面K型圆钢管搭接节点在弦杆轴向荷载作用下节点的承载力进行研究,对比分析不同几何参数与节点焊接形式下的极限承载力和破坏形式. 相似文献
10.
To investigate the seismic behavior of specially shaped column joints with X-shaped reinforcement,two groups of specimens with or without X-shaped reinforcement in joint core region were tested under constant axial compression load and low reversed cyclic loading,which imitated low to moderate earthquake force.The seismic behavior of specially shaped column joints with X-shaped reinforcement in terms of bearing capacity,displacement,ductility,hysteretic curve,stiffness degradation and energy dissipation was studied and compared to that without Xshaped reinforcement in joint core region.With the damage estimation model,the accumulated damage was analyzed.The shearing capacity formula of specially shaped column joints reinforced by X-shaped reinforcement was proposed with a simple form.The test results show that X-shaped reinforcement is an effective measure for improving the seismic behavior of specially shaped column joints including deformation behavior,ductility and hysteretic characteristic.All specimens were damaged with gradual stiffness degeneration.In addition,X-shaped reinforcement in the joint core region is an effective way to lighten the degree of cumulated damage.The good seismic performance obtained from the specially shaped column joint with X-shaped reinforcement can be used in engineering applications.The test value is higher than the calculated value,which indicates that the formula is safe for the design of specially shaped column joints. 相似文献
11.
Numerical Simulation of Dynamic Response and Collapse for Steel Frame Structures Subjected to Blast Load 总被引：4，自引：0，他引：4
The progressive collapse of steel frame structures under the blast load was investigated using LS-DYNA. The multi-material Eulerian and Lagrangian coupling algorithm was adopted. A flu-id-structure coupling finite element model was established which consists of Lagrange element for simulating steel frame structures and concrete ground, multiple ALE element for simulating air and TNT explosive material. Numerical simulations of the blast pressure wave propagation, struc-tural dynamic responses and deformation, and progressive collapse of a five-story steel frame structure in the event of an explosion near above ground were performed. The numerical analysis showed that the Lagrangian and Eulerian coupling algorithm gave good simulations of the shock wave propagation in the mediums and blast load effects on the structure. The columns subjected to blast load may collapse by shear yielding rather than by flexural deformation. The columns and joints of steel beam to column in the front steel frame structure generated enormous plastic defor-mation subjected to intensive blast waves, and columns lost carrying capacity, subsequently lead-ing to the collapse of the whole structure. The approach coupling influence between struc-tural deformation and fluid load well simulated the progressive collapse process of structures, and provided an effective tool for analyzing the collapse mechanism of the steel frame structure under blast load. 相似文献
12.
The progressive collapse of steel frame structures under the blast load was investigated using LS-DYNA.The multi-material Eulerian and Lagrangian coupling algorithm was adopted.A fluid-structure coupling finite element model was established which consists of Lagrange element for simulating steel frame structures and concrete ground,multiple ALE element for simulating air and TNT explosive material.Numerical simulations of the blast pressure wave propagation,structural dynamic responses and deformation,and progressive collapse of a five-story steel frame structure in the event of an explosion near above ground were performed.The numerical analysis showed that the Lagrangian and Eulerian coupling algorithm gave good simulations of the shock wave propagation in the mediums and blast load effects on the structure.The columns subjected to blast load may collapse by shear yielding rather than by flexural deformation.The columns and joints of steel beam to column in the front steel frame structure generated enormous plastic deformation subjected to intensive blast waves,and columns lost carrying capacity,subsequently leading to the collapse of the whole structure.The approach coupling influence between structural deformation and fluid load well simulated the progressive collapse process of structures,and provided an effective tool for analyzing the collapse mechanism of the steel frame structure under blast load. 相似文献
13.
对15根玻璃纤维布加固的钢筋混凝土梁进行了试验研究。试验结果表明,玻璃纤维布加固的钢筋混凝土梁抗弯承载力显著提高,加固效果明显,但要有足够的粘贴长度以避免发生剥离破坏。 相似文献
14.
The National Swimming Center built for the 2008Beijing Olympic Games applies the polyhedron spatialframe structure, which is based on the foam physicstheory[1]. Its simple geometry is a square box of 170m×170 m×29 m. It can hold 17 000 people, theroof o… 相似文献
15.
《天津大学学报(英文版)》2015,(4)
Nonlinear finite element analysis and parametric studies were carried out to study the influence of axial load ratio on the shear behavior of the through-diaphragm connections of concrete-filled square steel tubular columns. The analysis reveals that smaller axial load ratio can improve the shear bearing capacity and ductility while larger axial load ratio will decrease the shear behavior of the through-diaphragm connections. The parametric studies indicate that the axial load ratio should be limited to less than 0.4 and its influence should be considered in the analysis and design of such connections. 相似文献
16.
采用Ansys有限元软件对8根不同锈蚀率的FRP片材加固钢筋混凝土梁的受弯性能进行数值分析,研究纵筋锈蚀率对FRP加固梁的裂纹开展、破坏模式、承载能力以及延性和变形能力的影响.研究结果表明:低钢筋锈蚀率的梁发生受压区混凝土压碎破坏;中等锈蚀率的梁钢筋屈服后,钢筋与混凝土界面发生黏结滑移,最后FRP剥离破坏;高锈蚀率的梁钢筋没有达到屈服强度便发生黏结滑移,最后发生受压区混凝土压碎破坏.钢筋锈蚀越严重,FRP加固钢筋混凝土梁的承载力降低得越多.试件RCB-1(锈蚀率为0)的承载力为115 kN,而试件RCB-7(锈蚀率为20%)的承载力仅为42 kN.与FRP加固未锈蚀的钢筋混凝土梁相比,FRP加固锈蚀钢筋混凝土梁的变形能力较高.试件RCB-1和试件RCB-7的最大跨中挠度分别为20 mm和35 mm,而试件RCB-5(锈蚀率为10%)的最大跨中挠度达到了60 mm. 相似文献
17.
INTRODUCTION Creep is an internal characteristic of concrete under long-term load. A long time has elapsed since the first discovery of concrete creep in 1907 by Hatt. Many researches have been devoted to this complex problem ever since. However, despite major suc-cesses, the creep phenomenon is still far from being fully understood, even though the phenomenon has occupied some of the best minds in the field, such as Glanville, Dischinger, Troxell, Pickett, Neville, etc. Creep phenome… 相似文献
18.
陈培旭张铮冯若若 《福建工程学院学报》2021,(3):268-274
以顶底角型件高强螺栓连接铝合金梁柱节点为研究对象,利用有限元软件建立数值模型,并根据试验实测数据验证了有限元的准确性。探讨了轴压比、节点域厚度和顶底角型件厚度对节点力学性能的影响。对算例计算所得弯矩-转角曲线进行分析,拟合回归了三参数模型中形状系数的近似解析公式。结果表明,节点在合适的轴压比、节点域厚度和顶底角型件厚度下能表现出良好的抗震性能。提出的形状系数近似计算公式较为准确可靠,可为实际工程的连接设计方法提供理论依据。 相似文献
19.
The expansion joints are expected to have movement capacity, bearing capacity for static and dynamic loading, water-tightness, low noise emission and traffic safety. In particular, the failure due to impact loading is the main reason for the observed damages. The problem of dynamic behavior of the expansion joints is so complex that we shall focus our attention on the impact factor for vehicle load that is governed by traffic impact. In order to overcome this difficulty, the cantilever-toothed aluminum joint (finger joint) is one of the promising joints under impact loading. In this study, from the viewpoint of design methodology, numerical studies for impact behavior were conducted for aluminum alloy expansion joints with perforated dowels. The design impact factor for the expansion joints with the perforated dowels against traffic impact loading was examined by using numerical simulations. 相似文献