共查询到19条相似文献,搜索用时 140 毫秒
1.
2.
众所周知,在集成运算放大器中,负反馈放大电路对整体性能影响巨大。负反馈放大电路能使放大电路增益下降,但同时可以改善放大电路的性能。利用Multisim软件对负反馈放大电路进行仿真分析,从实验结果可以更直观的理解负反馈的重要作用。 相似文献
3.
4.
在晶体管放大电路中,由于多种变化等原因,影响放大器的静态工作点及放大性能,使放大器工作不稳定。要正确分析反馈对放大电路的性能改变及正确引入反馈,必须能正确判断反馈的类型。 相似文献
5.
6.
7.
8.
电子电路中放大的一般是非常微弱的信号,因此需要用多级放大电路。多级集成放大电路多采用直接耦合方式,而零点漂移是直接耦合放大电路存在的最突出的问题。采用差动放大电路是抑制零点漂移最有效的方法。 相似文献
9.
10.
提出音频电压放大器的设计原则,并通过实例介绍了整个放大器的设计步骤,为放大电路的设计提供一种新模式。 相似文献
11.
一种射频大功率放大器电源偏置电路设计方法(英文) 总被引:2,自引:0,他引:2
设计射频大功率放大器时,为了传输大的电源电流而加宽的λ/4电源偏置微带线往往不能很好的对偏置电路和信号电路进行隔离,从而影响放大器的性能。本文对一种采用加厚微带线设计λ/4电源偏置电路的方法进行了分析,并根据一种卫星数传发射机的功率放大器设计要求,分别采用本文介绍的方法和传统方法设计了两个功率放大器,给出了分析和试验结果,结果表明加厚λ/4偏置微带线可以比传统方法令功率放大器获得更高的性能,具有较大参考意义。 相似文献
12.
13.
本文介绍了高频小信号LC谐振放大器的设计思路与具体电路实现,主要由衰减网络、LC谐振放大、电压跟随和电源四大模块组成。衰减器采用电阻式π型网络实现;LC谐振放大中选用功耗小的2N2222型三极管进行两级放大,LC谐振部分为放大器的负载;电压跟随采用集成运放OPA355,以实现电路阻抗的良好匹配;为了给放大器工作提供稳压电源,采用LM317稳压芯片设计了一个电源。经测试,放大器低功耗、高增益,具有良好的选择性。 相似文献
14.
低噪声放大器在接收系统中能降低系统的噪声和接收机灵敏度,是接收系统的关键部件。本文按照低噪声放大器电路的设计要求,完成了实际的电路设计并通过ADS仿真软件对电路进行仿真,得到了很好结果,对实际的电路设计有一定的意义。 相似文献
15.
介绍了一种高性能CMOS采样/保持电路,在0.35-μm工艺、3.3-V电源和18-mW功耗下,实现了50-MHz采样频率,输入直到奈奎斯特频率仍能达到10位精度的要求。电路采用全差分结构、底极板采样、栅压自举开关技术、增益自举的折叠共源共栅跨导核心运算放大器和钳制共模电平的电平控制放大器。 相似文献
16.
为降低模拟采样前置电路的噪声,文章用集成运算放大器分别设计了低通滤波器,高通滤波器和带通滤波器电路三种电路,并用Multisim 12软件分别对这些电路进行了仿真并分析了电路各项指标和特点。 相似文献
17.
现代CMOS工艺的发展使得在CMOS工艺上设计射频IC前端成为可能。但在传统CMOS工艺集成的片上螺旋电感品质因数(Q)偏低,大大影响其性能。通过引入负电导实现螺旋电感Q值提升,并将其应用于共栅低噪声放大器的设计。 相似文献
18.
Theory and explicit formulas for the design of optimum non-reciprocal negative-resistance amplifiers
Wai-Kai Chen 《Journal of The Franklin Institute》1977,303(3):243-266
General relations for the design of negative–resistance amplifiers using tunnel diodes are derived. Using these relations, explicit formulas for the element values of an optimum non-reciprocal negative–resistance amplifier having Butterworth or Chebyshev transducer power-gain characteristics of arbitrary order are presented. In developing the theory and formulas, we allow the frequency-dependent load impedance, and also include the series parasitic inductance used in the equivalent circuit representation of a tunnel diode. Thus, the design of such amplifiers is reduced to simple arithmetic. 相似文献
19.
Myron Pawley 《Journal of The Franklin Institute》1933,215(2):133-147
A selective amplifier is developed which is simple, and more flexible than other types. It utilizes an audio transformer with a variable series resistance in the primary circuit, and a variable secondary load capacitance both of which may be adjusted to give broad or narrow peaked amplification at any frequency within a wide range, or flat amplification throughout this range. Theoretical and experimental amplification curves are shown, and a transient solution gives the primary and secondary currents resulting when a voltage is suddenly applied to the amplifier. This analysis shows that the time constants for the circuit are comparable with those for other peaked amplifiers. Oscillograms are shown illustrating the transient behavior of the amplifier. 相似文献