排序方式： 共有6条查询结果，搜索用时 46 毫秒
1
1.
相位模板技术与布拉格光纤光栅的写入 总被引：4，自引：0，他引：4
由于相位模板法仅使用一个光学器件 ,因而减少了光纤光栅制造系统的复杂性 ,是光纤布拉格光栅写入法中最有前途、使用最广泛并且具有本征稳定性的一种方法 .本文总结了相位模板技术及各种光纤布拉格光栅的写入 .值得注意的是在相位干涉法中 ,只用一块相位模板 ,就可以调整写入光纤布拉格光栅的波长 .在这些系统中 ,写入光纤光栅的紫外线 ( UV )干涉条纹经由一些光学元件 ,其中 ,相位模板的作用通常是± 1级衍射光的分束器 相似文献
2.
Fiber Bragg grating(FBG) is used as a wavelength reference device to calibrate the position of gas absorption peak in the intracavity absorption gas sensor(ICAGS) based on erbium-doped fiberring laser.This system can detect both the reflectance spectrum of FBGs and absorption spectrum of measured gas during a single wavelength sweeping process by linearly varying the driving voltage of optic filter.The voltages corresponding to center wavelength positions of four FBGs in the spectrum are determined through ... 相似文献
3.
Irradiated by infrared laser, the surface reducibility and adsorbability of Cu-Cr complex could be improved, owing to the interaction of photo-fragmentation and laser texturing. Analyzed by the binding energy spectra and the auger spectra, the valence states of chromium ion and copper ion were+3 and+1 after radiation respectively, which still had the reducibility to release electrons. In contrast with the near-infrared(NIR)1 064 nm and mid-infrared(MIR) 10 600 nm laser at the same average output power of 15 W, the reduced metal percentage in the Cu-Cr complex was obviously distinguished at the depth from nanometer to micron. After chemical plating, the average coating thickness and mean-square deviation of the NIR sample were 11.61 μm and 0.30 for copper layer, and 2.69 μm and 0.08 for nickel layer. The results were much better than those of the MIR sample. 相似文献
4.
A CO2 laser die-cutting system, which does not need die board any more, is a new technique for manufac-turing packing box. Two optical paths, the galvanometer scanning system and the flying optical system, are used to satisfy different processing needs. The scanning system is composed of galvanometer scanning mirrors and F-θ lens. And the flying optical system is driven by two servo motors. This paper presents the software and hardware design of the laser die-cutting system, the difference between the two optical paths, as well as the relationship among the cutting speed, thickness of wrapping paper and laser power. The cutting speed and thickness of wrapping paper are linearly increased by the incremental laser power, while the cutting speed is hyperbolically decreased by the incremental thickness of wrapping paper when the laser power is constant. The amount of incision is reduced by 20% and the processing time by 40% when tested by a low power RF CO2 laser die-cutting system using the optimized program. This tech- nique is also used for the reference of other rapid laser processing systems. 相似文献
5.
6.
A system for mobile robot localization and navigation was presented.With the proposed system,the robot can be located and navigated by a single landmark in a single image.And the navigation mode may be following-track,teaching and playback,or programming.The basic idea is that the system computes the differences between the expected and the recognized position at each time and then controls the robot in a direction to reduce those differences.To minimize the robot sensor equipment,only one omnidirectional camera was used.Experiments in disturbing environments show that the presented algorithm is robust and easy to implement,without camera rectification.The rootmean-square error(RMSE) of localization is 1.4,cm,and the navigation error in teaching and playback is within 10,cm. 相似文献
1